Leeson SM Series Quick Reference Guide Manuel d'utilisateur télécharger pdf

Variable Speed AC Motor Drives

SM Series

Quick Reference Guide

7KLVJXLGHLVLQWHQGHGDVDQDLGWRFRQILJXUHWKH606HULHVGULYH

NOTE: %HIRUHLQVWDOOLQJDQGRSHUDWLQJWKH60GULYHSOHDVH

UHDGDQG EHFRPH IDPLOLDU ZLWKWKH 60 6HULHV LQVWDOODWLRQ

DQGRSHUDWLRQPDQXDO

6KRZQEHORZDUHWZRVDPSOHZLULQJGLDJUDPVLQFOXGLQJ

IRUZDUGUHYHUVHGLUHFWLRQFRQWURO2QHVKRZVDWKUHHZLUH

VWDUWVWRSFRQWUROXVLQJPRPHQWDU\FRQWDFWVDQGWKHRWKHUVKRZVD

ZLUHVWDUWVWRSFRQWUROXVLQJPDLQWDLQHGFRQWDFWV 5HTXLUHG

SDUDPHWHUVHWWLQJVDUHDOVRLQFOXGHG

:,5(67

$576723

6HW3DUDPHWHU7%$

WR6WDUW5HYHUVH

6HW3DUDPHWHU7%(

WR6WDUW)RUZDUG

6HW3DUDPHWHU5RWDWLRQ

WR)RUZDUGDQG5HYHUVH

SM TERMINAL STRIP DIAGNOSTIC AND DISPLAY MESSAGES

BULLETIN #2454

3577S/1000/6-02/RL/BH

STOP

SIGNAL COMMON

0-10 VDC SPEED REFERENCE INPUT

SPEED POT POWER SUPPLY

DIGITAL INPUT REFERENCE

TB-13A FUNCTION SELECT

TB-13B FUNCTION SELECT

TB-13E FUNCTION SELECT

4-20 mA SPEED REFERENCE INPUT

DISPLAY DESCRIPTION

Speed Reference Codes

CP CONTROL PAD: The drive speed is controlled by the and  buttons on the front of the drive.

EI EXTERNAL CURRENT: The drive speed is controlled by a 4-20 mA signal between TB-25 and TB-2

EU EXTERNAL VOLTAGE: The drive speed is controlled by a 0-10 VDC signal between TB-5 and TB-2.

JG JOG: The drive is in Jog mode and the speed is set by preset speed #2 (Parameter 32).

OP MOP: Contacts wired to TB-13B and 13C are used to increase and decrease the drive speed.

Pr1-Pr7 PRESET SPEEDS #1-7: The drive speed is set by the selected Preset Speed (Parameters 31-37).

Status Indication

br DC BRAKING: The DC braking circuit is activated.

CURRENT LIMIT: The output current has exceeded the CURRENT LIMIT setting (Parameter 25)

and the drive is reducing the output frequency to reduce the output current. If the drive

remains in CURRENT LIMIT for too long, it can trip into a CURRENT OVERLOAD fault (PF).

Er ERROR: Invalid data has been entered.

“GE” will be displayed if an attempt is made to change the OEM default settings when the

drive is operating in the OEM mode (see Parameter 48).

LC FAULT LOCKOUT: Failed three restart attempts. Requires a manual reset.

SE SERIAL: The optional remote keypad is active as the user interface instead of the buttons on the

front of the drive.

SP START PENDING: This is displayed during the 15 second interval between restart attempts.

Diagnostic Codes

AF HIGH TEMPERATURE FAULT: Ambient temperature is too high.

CONTROL FAULT: A blank EPM, or EPM with corrupted data has been installed. Perform a

factory reset (Parameter 48).

cF INCOMPATIBILITY FAULT: An EPM with a different parameter version has been installed.

dF DYNAMIC BRAKING FAULT: The drive has sensed the dynamic braking resistors are overheating.

EXTERNAL FAULT: TB-13A and/or TB13C is set as an external fault input and TB-13A and/or

TB-13C is open with respect to TB-2.

GF DATA FAULT: User data and OEM defaults in the EPM are corrupted.

HIGH DC BUS VOLTAGE FAULT: Line voltage is too high; Deceleration rate is too fast;

Overhauling load. Fast deceleration and overhauling loads may require dynamic braking.

REMOTE KEYPAD FAULT: The communication link between the drive and the optional Remote

Keypad has been lost. Check for proper wiring and/or noise.

LF LOW DC BUS VOLTAGE FAULT: Line voltage is too low.

OUTPUT TRANSISTOR FAULT: Phase to phase or phase to ground short circuit on the

output: Failed output transistor: Boost settings are too high: Acceleration rate is too fast.

CURRENT OVERLOAD FAULT: VFD is undersized for the application: Mechanical problem with

the driven equipment.

SF SINGLE-PHASE FAULT: Single-phase input power has been applied to a three-phase drive.

START FAULT: Start command was present when the drive was powered up. Must wait

2 seconds after power-up to apply Start command if START METHOD is set to NORMAL.

F1 EPM FAULT: The EPM is missing or damaged.

FC,F2-Fo INTERNAL FAULTS: The control board has sensed a problem. Consult factory.



:,5(67$576723

6HW3DUDPHWHU7%$

WR5XQ5HYHUVH

6HW3DUDPHWHU5RWDWLRQ

WR)RUZDUGDQG5HYHUVH

13A

13B

13E

PROGRAMMABLE FORM A RELAY

1 2 5 6 11 13A 13B 13E 25

Momentary Momentary

Stop Contact Start Contact

1 2 5 6 11 13A 13B 13E 25

Maintained Maintained

Run Forward Run Reverse

Contact Contact

REV FWD

A Subsidiary of REGAL-BELOIT CORPORATION

1 2

Résumé du contenu

Page 1 - Quick Reference Guide

Variable Speed AC Motor DrivesSM SeriesQuick Reference Guide7KLVJXLGHLVLQWHQGHGDVDQDLGWRFRQILJXUHWKH606HULHVGULYHNOTE: %HIRUHLQVWDOOLQJ

Page 2 - SM PARAMETER MENU

CONFIGURING THE SM DRIVEEntering Program Mode:7RDFFHVVWKHSDUDPHWHUVSUHVVWKHMode EXWWRQ7KLVZLOODFWLYDWHWKHSDVVZRUGSURPSW7KHGLVSOD\ZLOO

Commentaires sur ces manuels

Pas de commentaire

Leeson SM Series Quick Reference Guide Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Logiciel Leeson SM Series Quick Reference Guide. LEESON SM Series Quick Reference Guide User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Logiciel Leeson SM Series Quick Reference Guide